Ball screw pair: key technology in the field of mechanical transmission

May 14, 2025

Leave a message

Claire
Claire
Linear Motion Application Engineer, DLY Automation Specializing in ball screw and linear guideway selection, system integration, and OEM technical support for CNC and automation applications.

A ball screw pair converts rotary motion into controlled linear motion through rolling contact between the screw shaft, steel balls and ball nut. Its performance is not determined by the screw alone. Raceway geometry, ball circulation, preload, lead accuracy, support arrangement, lubrication and installation alignment work together as one transmission system.

These technologies determine whether a machine axis can reach the required position repeatedly, reverse direction without excessive lost motion and operate at the intended speed without vibration or overheating. This is why two ball screw assemblies with the same nominal diameter and lead may behave very differently in actual equipment.

Understanding the key technologies of a ball screw pair helps engineers specify the assembly according to load, stroke, speed and positioning requirements instead of selecting it only by model number.

Ball Screw Pair Components

A complete ball screw pair normally contains a screw shaft, ball nut, steel balls, ball return system and seals or wipers. In a machine axis, it also works with support bearings, a motor connection and a lubrication system.

Component Main Function Effect on Performance
Screw shaft Provides the helical raceway and transmits rotary motion Influences lead accuracy, load capacity, critical speed and column strength
Ball nut Contains the matching raceway and transfers axial load Affects rigidity, mounting method and available space
Steel balls Roll between the shaft and nut raceways Affect smoothness, load distribution, preload and fatigue life
Return system Recirculates the balls through a closed path Influences operating speed, noise and circulation stability
Wipers and seals Limit contaminant entry and lubricant loss Help protect the raceways and extend operating life

Rolling Contact and Raceway Geometry

The central technology of a ball screw pair is the replacement of sliding contact with recirculating rolling contact. When the screw or nut rotates, the balls move along the helical raceways and transfer force between the two components. After passing through the loaded zone, the balls return to the starting point through the circulation system.

This mechanism reduces friction and allows the assembly to operate efficiently under axial load. However, describing a ball screw as having "zero friction" is inaccurate. Rolling contact, seals, lubricant churning, preload and ball recirculation all produce resistance and heat.

Raceway profile accuracy is particularly important. The conformity between the ball and groove controls the contact area and load distribution. Poor geometry or inconsistent ball size can cause uneven loading, torque fluctuation, vibration and premature surface fatigue.

Ball Recirculation Technology

Because the balls continuously travel through the loaded raceway, they must return through a closed circulation path. Common return designs include external return tubes, internal deflectors and end-cap circulation structures.

No single circulation design is best for every machine. A compact internal design may suit equipment with limited installation space, while another structure may be selected for a particular lead, speed or load requirement. The transitions between the loaded track and return path must allow the balls to enter and leave smoothly.

At higher rotational speeds, unstable recirculation can increase impact, vibration, temperature and noise. High-speed performance therefore depends on more than the screw lead. It also requires suitable return-path geometry, ball spacing, lubrication and installation accuracy.

Lead Accuracy and Positioning

The theoretical linear travel for one screw revolution is equal to the nominal lead. Actual travel differs slightly because of lead error. Ball screw accuracy describes the permitted variation of this actual movement over a specified travel length.

Positioning performance should not be judged by accuracy grade alone. The final error of a machine axis can also include axial clearance, elastic deformation, support-bearing movement, thermal expansion, coupling error, mounting misalignment and feedback-system limitations.

Important distinction: lead accuracy describes travel error, backlash describes lost motion during reversal, and repeatability describes how consistently the axis returns to the same commanded position. These terms should not be used interchangeably.

Rolled ball screws are widely used in general automation and positioning systems, while ground ball screws are selected when the application requires tighter lead accuracy and more controlled raceway geometry. The appropriate grade should be based on the required axis performance rather than the assumption that the highest grade is always necessary.

Preload, Backlash and Rigidity

Internal axial clearance can produce lost motion when the axis reverses direction. Preload applies an internal force between the balls and raceways to reduce clearance and increase axial rigidity. It may be created through ball-size selection, an offset raceway design or a double-nut arrangement.

Higher preload is not automatically better. Increasing preload can improve reversal response and stiffness, but it also raises friction torque and heat generation. Excessive preload may shorten fatigue life, increase motor demand and make the assembly more sensitive to misalignment.

The correct preload depends on the external axial load, required rigidity, duty cycle, acceleration, operating speed and installation accuracy. Applications with modest positioning requirements may not need the same preload as a precision machine-tool feed axis.

Load Capacity and Fatigue Life

Ball screw load capacity is influenced by ball diameter, raceway geometry, number of loaded balls, number of circulation circuits and material condition. Catalogs normally provide a basic dynamic load rating for fatigue-life calculations and a basic static load rating for checking permanent deformation under high or stationary loads.

Actual operating life is strongly affected by the equivalent axial load. Shock loads, poor alignment and contamination can make the real load on individual balls much higher than the nominal machine thrust suggests. Because calculated fatigue life changes sharply with load, an incorrect load estimate can produce an unrealistic service-life result.

Selection should therefore consider the normal load, peak load, acceleration force, duty cycle and operating orientation. A vertical axis may also require a brake or counterbalance because the high efficiency of a ball screw can allow back-driving when drive torque is removed.

Speed and Critical Speed

A larger lead produces more linear travel per revolution, allowing a target feed rate to be reached at a lower rotational speed. However, lead also affects required drive torque, available mechanical resolution and nut design.

For a rotating screw, maximum speed may be limited by the ball circulation system and by the shaft's critical speed. Critical speed is the rotational speed at which the screw approaches a bending resonance and begins to whip or vibrate. It is influenced mainly by the screw root diameter, unsupported length and end-support arrangement.

A long, slender screw generally reaches its speed limit earlier than a short, larger-diameter screw. Increasing the root diameter, reducing the unsupported length or using a more rigid support arrangement can raise the allowable operating speed. The design should retain a suitable margin below the calculated limit rather than operating continuously at resonance.

Thermal Control and Lubrication

Heat changes the length of the screw shaft and can create positioning drift even when the original lead accuracy is high. Heat may come from preload, support bearings, seals, rapid cycling and insufficient or excessive lubrication.

Grease is commonly used where a simple maintenance arrangement is preferred, while oil lubrication may be adopted in centralized or higher-speed systems. Lubricant type, viscosity and replenishment interval should match the operating speed, load, temperature and surrounding environment.

Precision equipment may also use temperature monitoring, controlled warm-up, thermal compensation, shaft pretension or cooling measures. These methods address thermal behavior at the system level rather than relying only on a higher ball screw accuracy grade.

Support and Installation

The ball screw pair does not operate independently from its mounting structure. Support bearings locate the screw axially and radially, while the coupling connects it to the motor. Common support arrangements include fixed–free, fixed–supported and fixed–fixed configurations.

Installation misalignment can create side loading that the ball screw was not designed to carry. This may cause abnormal torque, uneven wear and excessive temperature. The screw shaft, nut housing, support bearings and linear guide system should share the correct alignment.

End machining must also match the selected bearing supports and motor connection. DLY ball screws can be supplied with application-specific end machining and matched ball screw support units for integration into the machine structure.

Key Parameters for Selection

Parameter Why It Matters Information to Confirm
Screw diameter Affects load capacity, rigidity, buckling resistance and critical speed Axial load, total length and support distance
Lead Affects linear speed, motor rpm, torque and resolution Target speed, acceleration and motor characteristics
Accuracy grade Controls permissible lead variation Positioning tolerance and effective travel
Preload or clearance Influences backlash, rigidity, torque and temperature Reversal accuracy, duty cycle and external load
Nut form Determines mounting interface and available load capacity Housing dimensions and mounting direction
Support arrangement Affects axial stiffness, critical speed and thermal behavior Stroke, shaft length, speed and installation space
Operating environment Determines sealing, lubrication and protective requirements Dust, chips, moisture and ambient temperature

Applications

Ball screw pairs are used where controlled linear movement, axial load capacity and repeatable positioning are required. Typical applications include CNC feed axes, industrial automation, packaging machinery, inspection equipment, semiconductor equipment, medical devices and robotic positioning systems.

The required technology level differs by application. A general transfer mechanism may prioritize cost, load capacity and reliability, while a machine-tool axis may place greater emphasis on lead accuracy, preload, thermal stability and structural rigidity. Selection should begin with the operating conditions rather than the application name alone.

FAQ

Is a ball screw pair the same as a ball screw?

The terms are often used interchangeably. "Ball screw pair" emphasizes the matched screw shaft and ball nut assembly, including the balls and circulation components, rather than the screw shaft alone.

Does a ball screw have zero backlash?

Not every ball screw is backlash-free. Axial clearance depends on the internal design and assembly condition. Suitable preload can reduce or eliminate measurable clearance, but it also increases friction torque and heat.

What determines ball screw positioning accuracy?

Important factors include lead accuracy, axial clearance, preload, elastic deformation, support-bearing rigidity, thermal expansion, mounting alignment and the machine's feedback and control system.

Why can a ball screw overheat?

Common causes include excessive preload, unsuitable lubrication, misalignment, damaged circulation components, excessive speed and high seal resistance. The source should be checked before changing the lubricant or preload.

Conclusion

The key technology of a ball screw pair is not limited to low-friction motion. Reliable performance comes from the interaction of raceway geometry, ball circulation, accuracy, preload, stiffness, load capacity, speed control, lubrication and mounting structure.

For selection, confirm the axial load, effective stroke, target speed, accuracy requirement, duty cycle, mounting space, support arrangement and working environment. DLY can provide rolled C7 and ground C5 ball screw solutions, including nut configuration, preload, end machining and support-unit matching.

For ball screw selection or technical confirmation, send the required diameter, lead, stroke, load, speed, accuracy grade and end-machining drawing.

 export@dlybearing.com

References

  • ISO 3408-1 - Ball screws: Vocabulary and designation.
  • ISO 3408-3 - Ball screws: Acceptance conditions and acceptance tests.
  • Manufacturer engineering catalogs and technical manuals covering ball screw accuracy, preload, load rating and critical speed.

← Back to DLY Blog

Send Inquiry