Replacing a ball screw is relatively straightforward when the original manufacturer and complete model number are still available. The buyer can check the catalog, confirm the dimensions and order the same assembly.
The situation becomes more difficult when the model marking is worn away, the machine manufacturer no longer supplies spare parts or the original ball screw has been discontinued. In these cases, identifying a replacement requires more than measuring the screw diameter and lead.
A replacement ball screw must match the machine's usable stroke, nut mounting structure, support bearings, coupling and shaft-end dimensions. Even when two screws share the same nominal model, differences in total length or end machining can prevent installation.
Start with Any Available Identification
Before measuring the old ball screw, check every accessible surface for identification. Markings may appear on the nut body, flange, screw end, bearing support, machine nameplate or maintenance records.
A marking such as SFU1605 usually indicates a nominal screw diameter of 16 mm and a lead of 5 mm. However, it normally identifies only the basic ball screw series and size. It does not define the complete shaft length, machined ends, accuracy grade or installation structure.
Record the complete marking exactly as it appears. Do not remove letters or assume that an unfamiliar suffix is unimportant. A suffix may describe the nut structure, preload, accuracy, seal arrangement or a manufacturer-specific design.
Practical tip: Take clear photographs of the complete assembly, nut marking, flange, fixed end, supported end and bearing supports before removing the ball screw from the machine. These photographs can help explain the original installation when no drawing is available.
Measure the Screw Diameter
The nominal screw diameter is one of the first dimensions needed to identify the ball screw. Measure across the outside of the threaded screw shaft using a suitable caliper or micrometer. Avoid measuring across damaged, heavily worn or contaminated areas.
Common model descriptions combine the nominal diameter and lead. For example, a 1605 ball screw generally has a nominal diameter of 16 mm and a lead of 5 mm. A 2510 ball screw generally indicates a 25 mm diameter and a 10 mm lead.
The measured outside diameter may not be exactly equal to the nominal model number because the measurement is taken over the helical raceway rather than a simple cylindrical surface. Use it to identify the likely nominal size, not as the only manufacturing dimension.
Determine the Ball Screw Lead
Lead is the linear distance that the nut travels during one complete revolution of the screw. It must not be confused with the visible spacing between neighboring thread grooves.
The most practical identification method is to mark the screw and nut positions, rotate the screw exactly one revolution and measure the resulting axial movement. If the assembly cannot rotate safely, the lead can be estimated by measuring the axial distance across several repeating raceway positions and dividing by the number of intervals.
Lead must be confirmed carefully because changing it affects linear travel per revolution, motor speed, thrust, positioning resolution and machine-control parameters. A replacement with the wrong lead may physically fit but will not produce the same axis movement.
Measure the Overall Length and Threaded Section
Overall length is the distance from one end of the finished screw shaft to the other. This dimension includes the threaded raceway and both machined ends.
The threaded section should be measured separately. Buyers sometimes provide only the overall length, but two screws with the same overall length can have different raceway lengths and different usable strokes.
When possible, also record the original nut travel limits and the machine's required axis stroke. The replacement must provide enough travel without allowing the nut to overrun the usable raceway or collide with a bearing support, nut housing or machine structure.
| Length | What It Describes | Why It Must Be Confirmed |
|---|---|---|
| Overall screw length | Complete length including both machined ends | Must fit the available machine space |
| Threaded raceway length | Length of the ball-running section | Limits the possible nut travel |
| Required stroke | Actual operating travel of the machine axis | Determines the usable movement requirement |
| Fixed-end length | Machined section for bearings, thread and coupling | Must match the fixed support and drive connection |
| Supported-end length | Machined section for the opposite support bearing | Must match the supported-side bearing structure |
Identify the Ball Nut Structure
A replacement screw shaft must work with a compatible ball nut. If the complete screw-and-nut assembly will be replaced, the new nut must also fit the existing nut housing, moving table or mounting bracket.
First identify whether the original assembly uses a single nut, double nut, cylindrical nut or flanged nut. Then measure the nut body length, outside diameter, flange diameter, flange thickness, pilot diameter and mounting-hole arrangement.
The flange shape and bolt pattern are especially important. Two nuts may fit the same nominal screw diameter and lead but use different flange widths, hole positions or body lengths. Replacing one with the other may require a new nut housing or changes to the moving structure.
The ball-return design should also be recorded when it can be identified. External-return, internal-circulation and end-cap ball nuts have different body structures and installation envelopes. A technically suitable substitute may therefore require dimensional confirmation rather than selection by model number alone.
The Machined Ends Usually Determine Whether the Replacement Fits
Ball screw end machining is one of the most common reasons why a nominally correct replacement cannot be installed. The fixed and supported ends are normally processed to match the machine's bearings, support units, lock nut, coupling and motor arrangement.
The fixed end generally contains several stepped sections. These may include an angular-contact bearing seat, shaft shoulder, lock-nut thread, seal position and coupling connection. The opposite end commonly contains a simpler bearing seat, although its dimensions still need to match the supported-side bearing.
A complete end-machining drawing is the safest reference. If the original drawing is unavailable, measure each diameter and axial length from the shaft shoulder to the end of the screw. Threads, keyways, retaining-ring grooves, flats, chamfers and fillets should be recorded separately.
| Machined Feature | Information to Measure | Connected Component |
|---|---|---|
| Fixed bearing seat | Diameter, length, shoulder and fit requirement | Fixed-side support bearings |
| Lock-nut thread | Major diameter, pitch, thread length and direction | Bearing lock nut |
| Coupling end | Shaft diameter, engagement length, keyway or flat | Motor coupling |
| Supported bearing seat | Diameter, length and shoulder position | Supported-side bearing |
| Retaining-ring groove | Groove diameter, width and axial position | Circlip or retaining ring |
Check the Fixed and Supported Bearing Units
If the machine uses standard BK/BF, FK/FF or EK/EF support units, record the model numbers from both ends. These model numbers can help identify the expected bearing-seat and lock-nut dimensions.
Do not assume that every support unit with the same model name uses identical internal dimensions. Products from different manufacturers may vary in bearing arrangement, internal preload, shoulder position or supplied accessories. The existing end-machining dimensions should still be checked.
If the support bearings are worn, replacing only the screw may not restore the axis performance. Inspect the bearings for rough rotation, axial play, noise and damage. DLY can supply a machined ball screw together with matching ball screw support units when a complete replacement set is required.
Confirm the Required Accuracy and Backlash
Dimensions alone do not define the performance of a replacement ball screw. The required accuracy grade, axial clearance and preload should be selected according to the machine's positioning requirement.
A general automation axis may use a rolled C7 ball screw, while a precision machine tool may require a ground C5 or C3 assembly. Replacing a precision screw with a lower-grade product can reduce positioning accuracy even if all installation dimensions match.
The original nut structure can provide useful clues. A double-nut or preloaded nut often indicates that the machine requires greater axial rigidity and reduced backlash. It should not automatically be replaced with a standard non-preloaded single nut solely because the nominal diameter and lead are the same.
If the original accuracy grade is unknown, provide the machine type, axis function and required positioning tolerance. This information helps determine whether a standard rolled replacement is sufficient or whether a precision ground and preloaded assembly should be considered.
Inspect the Cause of the Original Failure
Before ordering a replacement, determine why the original ball screw failed. Normal wear after long service is different from damage caused by contamination, misalignment, poor lubrication or failed support bearings.
If metal chips, dust or coolant entered the nut, installing a new ball screw without improving the protective cover may result in another early failure. If the old screw shows uneven wear or the nut binds at certain positions, inspect the alignment between the ball screw, nut housing and linear guides.
The motor coupling and support bearings should also be checked. A damaged coupling, loose lock nut or incorrect bearing preload can cause vibration, noise, axial movement or positioning error that may initially be mistaken for ball screw failure.
Can the Old Ball Nut Be Reused?
Reusing the original nut may appear to simplify installation because its flange and mounting dimensions already fit the machine. However, a ball nut and screw raceway operate as a matched rolling-contact assembly.
A worn nut may contain damaged raceways, worn return components or unsuitable balls. Installing it on a new screw shaft can produce incorrect clearance, uneven movement or premature wear. Compatibility must be confirmed before the old nut is reused.
For most replacement projects, supplying a matched screw-and-nut assembly is more reliable. The new nut can be produced or selected to fit the existing mounting structure while the screw ends are machined according to the original dimensions.
Important handling note: Do not rotate a recirculating ball nut off the screw unless a suitable transfer sleeve and correct procedure are available. Removing the nut incorrectly can allow the balls to fall out or disturb their circulation sequence.
What If the Old Ball Screw Cannot Be Removed?
Sometimes the machine must remain assembled while a replacement quotation is prepared. In that case, collect as much information as possible from the exposed areas.
Photograph the nut, screw shaft, support units, coupling and complete axis layout. Measure the accessible screw diameter and determine the lead by rotating the shaft and measuring the table movement. Record the machine manufacturer, model, axis direction and required stroke.
These details may be sufficient for a preliminary assessment, but final end-machining dimensions normally require a drawing, removal of the old screw or measurement of the support components. Production should not begin from estimated dimensions when the replacement must fit an existing machine without modification.
Information Needed for a Replacement Ball Screw Quotation
A clear replacement request reduces repeated communication and allows the supplier to judge whether a standard ball screw can be modified or a custom assembly is required.
- Complete original model number or all visible markings
- Nominal screw diameter and lead
- Overall length and threaded raceway length
- Nut type, body dimensions, flange dimensions and bolt-hole pattern
- Fixed-end and supported-end machining dimensions
- Support-unit and bearing model numbers
- Required accuracy grade, backlash or preload
- Machine type, axis direction, stroke, load and operating speed
- Clear photographs or a dimensional drawing
- Required quantity
If some information is unavailable, identify which dimensions have been measured and which are estimates. This allows the supplier to highlight the details that still require confirmation before production.
Common Replacement Mistakes
The most common mistake is ordering by nominal model alone. A buyer may identify the original product as SFU1605 and order another SFU1605, only to find that the screw is too long, the shaft ends do not fit the bearings or the nut flange does not match the existing housing.
Another mistake is changing the lead without considering the machine control and motor requirements. A different lead changes the distance moved per motor revolution and may require control-parameter changes. It also changes the relationship between speed, thrust and positioning resolution.
Replacing only the ball screw while ignoring worn support bearings, a damaged coupling or poor alignment may leave the original symptoms unchanged. The complete axis should be inspected before deciding which components require replacement.
Finally, photographs should not be used as a substitute for critical dimensions. Photos are useful for identifying the general structure, but they cannot reliably define bearing fits, threads or shaft-shoulder positions.
Standard Replacement or Custom-Machined Ball Screw?
A standard ball screw may be suitable when the machine uses common dimensions and the buyer can modify the surrounding structure. Existing CNC machines and industrial equipment, however, often require the new assembly to fit without changing the bearing supports, nut housing or motor position.
In these cases, a custom-machined replacement is usually more practical. The screw diameter, lead and nut structure can be selected to match the operating requirement, while the total length and both shaft ends are processed according to the original drawing or measured sample.
DLY supplies custom ball screw assemblies with drawing-based cutting, end machining, nut matching and related component support. Rolled C7 and ground C5 options can be considered according to the machine's accuracy requirement.
Send the Old Ball Screw Details to DLY
When the original ball screw model is unknown or no longer available, DLY can help review the existing dimensions and determine what information is still needed for replacement.
Send clear photographs of the complete ball screw, nut, fixed end, supported end and support units. Include the screw diameter, lead, overall length, nut dimensions, end-machining dimensions, machine type and required quantity.
If a complete drawing is unavailable, provide the dimensions you can measure and identify any uncertain areas. The technical details can then be checked before a replacement quotation or production drawing is confirmed.
Need a Replacement Ball Screw?
Send DLY the old screw photos, diameter, lead, overall length, nut dimensions, end-machining details and required quantity.


