Ball Screw Backlash: What It Is and How to Prevent It

Mar 28, 2026

Leave a message

Claire
Claire
Linear Motion Application Engineer, DLY Automation Specializing in ball screw and linear guideway selection, system integration, and OEM technical support for CNC and automation applications.

Ball screw backlash is a small axial clearance or lost motion that appears when the direction of motion changes. In CNC machines, automation equipment, inspection systems, and precision positioning axes, even a small amount of ball screw backlash can affect positioning accuracy, repeatability, surface quality, and long-term machine stability.

Backlash is not only related to the ball screw itself. Nut clearance, preload structure, wear, lubrication, support bearings, end machining, coupling alignment, and installation accuracy can all influence the final backlash level of a ball screw system.

This article explains what ball screw backlash is, why it matters, what causes it, how to check it, and how preload, double nut design, lubrication, installation alignment, and regular maintenance help reduce and control backlash.

What Is Ball Screw Backlash?

Ball screw backlash refers to the small axial movement or lost motion that occurs when the rotation direction of a ball screw system is reversed. When the screw changes direction, any internal clearance between the balls and raceways must be taken up before the nut begins to move accurately in the opposite direction.

In a well-matched ball screw and nut system, the motion should be transmitted smoothly with minimal delay. However, manufacturing clearance, insufficient preload, wear, poor lubrication, or installation errors can create measurable axial play.

This backlash may be measured in microns or millimeters. Although it may look small, it can cause visible positioning errors in machines that require accurate direction reversal and repeatable movement.

Ball screw backlash diagram showing axial lost motion during direction reversal
Ball Screw Backlash During Direction Reversal

Why Backlash Matters in CNC and Automation Systems

Backlash matters because many machines do not only move in one direction. CNC axes, automated positioning tables, robotic transfer units, inspection platforms, and packaging systems often change direction repeatedly during operation.

When backlash exists, the motor or screw may begin reversing before the table, nut, or carriage actually responds. This delay can create positioning error and unstable movement, especially during contouring, drilling, engraving, inspection, or repeated pick-and-place motion.

Backlash may cause:

Positioning error after direction reversal.

Poor repeatability over repeated cycles.

Visible machining marks or dimensional deviation in CNC cutting.

Unstable reversal movement, noise, or vibration.

Lower surface quality and reduced machine confidence in precision applications.

Main Causes of Ball Screw Backlash

Ball screw backlash may come from the original internal clearance, but it can also develop gradually during machine use. The table below shows common causes and what to check.

Cause How It Creates Backlash What to Check
Manufacturing clearance A small gap between balls and raceways allows smooth rolling, but it may create axial play during reversal. Accuracy grade, nut clearance, preload condition, and application requirement.
No preload Without controlled internal force, the balls may not stay in constant contact with both raceway sides. Nut type, preload design, axial play, and reversal response.
Wear and aging Long-term rolling contact gradually wears balls and raceways, increasing internal clearance. Running time, noise, axial movement, backlash measurement, and nut condition.
Poor lubrication Insufficient or contaminated lubrication increases friction and accelerates wear. Grease condition, contamination, lubrication interval, and working environment.
Installation error Misalignment creates uneven load, local stress, and faster wear of balls and raceways. Support bearings, coupling alignment, end machining, mounting accuracy, and bearing seat condition.

How to Check Ball Screw Backlash

Backlash is often noticed when a machine becomes less repeatable, especially after reversing direction. In CNC and automation systems, it can be checked by observing axis response, part accuracy, or direct movement measurement.

Possible signs of ball screw backlash:

The axis moves with a delay after direction reversal.

CNC parts show inconsistent dimensions in repeated cutting.

Repeatability becomes worse after long machine use.

There is axial play when pushing the table or nut by hand.

A dial indicator shows movement before the axis actually responds accurately.

When checking backlash, it is also important to inspect other related parts. Sometimes the measured lost motion is not only from the ball screw nut, but also from loose support bearings, worn couplings, motor connection problems, or poor machine frame rigidity.

How to Reduce and Prevent Ball Screw Backlash

Backlash control should be considered both before purchase and during machine use. A suitable preload structure may reduce backlash from the beginning, while correct installation and maintenance help prevent backlash from increasing over time.

Before Purchase or Design Stage

At the design stage, backlash control starts with the correct ball screw, nut, preload, support bearing, and end machining design. The machine's accuracy requirement, load direction, speed, reversal frequency, and installation space should be checked together.

Design-stage checks:

Choose a suitable accuracy grade according to positioning requirement.

Use a preloaded nut if backlash control is important.

Choose a double nut structure when higher rigidity and lower backlash are required.

Confirm end machining and support units before production.

Check load, speed, direction reversal frequency, and installation direction.

During Use and Maintenance Stage

During machine operation, backlash may increase if lubrication is poor, components are worn, or alignment becomes unstable. Regular inspection helps find problems before accuracy loss becomes serious.

Maintenance-stage checks:

Keep lubrication stable and suitable for the working environment.

Check whether support bearings are loose or worn.

Inspect nut wear, screw raceway condition, and abnormal noise.

Check coupling, motor connection, and bearing seat alignment.

Replace worn nuts, balls, support bearings, or screw assemblies when backlash exceeds the acceptable range.

Main Preload Methods for Backlash Control

Preload is one of the main methods used to reduce or control ball screw backlash. Instead of allowing free clearance inside the nut, preload applies controlled internal force so that the balls remain in closer contact with the raceways.

Preload can improve rigidity and reduce measurable backlash, but it should be selected carefully. Excessive preload may increase friction, heat generation, motor load, and wear.

Oversized Ball Preload

Oversized ball preload uses balls that are slightly larger than standard balls. These balls create a controlled interference fit inside the nut, helping reduce clearance between the balls and raceways.

This method is compact and cost-effective, making it suitable for many general industrial applications. However, the preload level is limited compared with double nut structures.

Double Nut Preload

Double nut preload uses two nuts installed on the same screw shaft. By adjusting the relative position between the two nuts, internal clearance can be reduced and preload can be introduced.

This structure provides higher rigidity and better backlash control, and is often used in CNC machines, precision measuring equipment, and high-accuracy automation systems.

DFU Ball Nut

Double Nut Ball Screw Structure for Backlash Control

The trade-off is that double nut structures need more installation space and usually cost more than single nut designs.

Lead Offset Preload

Lead offset preload uses a specially designed nut geometry to create controlled preload inside the nut. It can maintain a compact structure while improving backlash control.

This method is more complex to manufacture, but it can be useful when the application requires compact structure, stable preload, and better positioning performance.

Preload Method Main Advantage Limitation Suitable Use
Oversized ball preload Compact and cost-effective Limited preload level General industrial equipment
Double nut preload Higher rigidity and lower backlash More space and higher cost CNC machines and precision axes
Lead offset preload Compact structure with stable preload More complex manufacturing High-precision compact systems

Choosing a Low-Backlash Ball Screw

Choosing a low-backlash ball screw should be based on the actual machine requirement. Higher precision is useful, but nut structure, preload level, support bearing, end machining, and maintenance condition are also important.

For standard industrial applications, a well-designed C7 rolled ball screw with suitable preload may be enough. For higher-accuracy applications, buyers may consider C5 ground ball screws or more controlled preload structures according to the application requirement.

Selection Item What to Confirm
Accuracy grade C7 for general industrial motion, C5 for higher precision needs
Nut structure Single nut, preloaded nut, double nut, or custom preload structure
Preload level Balance backlash control, friction, heat, and motor load
Support unit BK/BF, FK/FF, EK/EF, or custom support structure
End machining Bearing seat, shoulder, thread, coupling end, and support fit
Application CNC, automation, inspection, vertical axis, or high-cycle operation
Maintenance Lubrication, dust protection, inspection interval, and replacement plan

DLY Ball Screw Backlash Control Reference

DLY supplies C7 cold-rolled ball screws, C5 ground ball screws, ball nuts, support units, and customized end machining for different accuracy and backlash control requirements.

For backlash-sensitive applications, nut structure, preload level, support bearing, end machining, lubrication, installation alignment, and machine frame rigidity should be confirmed together. Backlash control is a system issue, not only a ball screw model issue.

Conclusion

Ball screw backlash is a small clearance or lost motion during direction reversal, but it can have a clear effect on positioning accuracy, repeatability, machining quality, and long-term motion stability.

Backlash may come from manufacturing clearance, lack of preload, wear, poor lubrication, or installation errors. To reduce and prevent backlash, buyers and engineers should check preload design, nut structure, support bearings, end machining, lubrication, installation alignment, and maintenance conditions together.

A low-backlash ball screw system should be selected and maintained as a complete motion system, including the screw, nut, balls, support units, coupling, lubrication, and machine structure.

Need Help Checking Ball Screw Backlash?

If you are confirming backlash, preload structure, double nut design, support unit, end machining, or replacement requirements, you can send the model, drawing, load, travel length, or machine application for reference.

 

Email: export@dlybearing.com

Send Inquiry