A ball screw nut cannot be judged by appearance alone. A practical quality check should confirm the model, screw diameter and lead, external dimensions, flange mounting, surface condition, ball circulation, running torque, axial clearance and lubrication arrangement.
Some checks can be completed during incoming inspection, but internal raceway accuracy, ball matching and material condition require production records or specialised inspection. Do not dismantle a new ball nut simply to inspect the balls, because incorrect reassembly can change the preload, clearance and circulation condition.
1. Verify the Model Before Inspecting Quality
The first step is to confirm whether the supplied nut is actually the model ordered. A well-manufactured nut is still unsuitable if its diameter, lead or mounting dimensions do not match the screw and machine.
Check the following information against the drawing, purchase order or existing part:
- Complete nut model and series
- Nominal screw diameter
- Screw lead
- Single-nut or double-nut structure
- Flange shape and orientation
- Circulation type
- Required preload or axial clearance
- Lubrication-port position
A code such as 1605 normally indicates a 16 mm nominal screw diameter and 5 mm lead, but it does not confirm the flange dimensions, circulation structure or preload. Nuts with the same basic diameter and lead are not automatically interchangeable.
2. Inspect the External Condition
Examine the complete nut body under adequate lighting. The surface should be free from significant impact marks, cracks, rust and damage that could affect mounting or operation.
Pay particular attention to:
- Flange mounting face
- Mounting holes and counterbores
- Nut body and locating diameter
- Return tube, end cap or internal return components
- Seals and wipers
- Lubrication hole and grease fitting
- Protective mandrel or transfer sleeve
Minor cosmetic marks outside the mounting and functional surfaces do not necessarily mean the nut is unusable. Damage to the flange face, seal, return system or locating surface requires more careful evaluation.


3. Measure the Mounting Dimensions
Use calibrated calipers, micrometers, height gauges or dedicated fixtures to check the external dimensions shown on the drawing.
| Dimension | Why it matters | Typical inspection method |
|---|---|---|
| Nut overall length | Affects installation space and stroke | Caliper or height gauge |
| Nut body diameter | Must fit the nut housing | Outside micrometer or caliper |
| Flange diameter and thickness | Affects mounting and axial position | Caliper or height gauge |
| Mounting-hole position | Must match the nut seat or bracket | Height gauge, fixture or CMM |
| Flange-face runout | Can affect alignment after mounting | Dial indicator on a suitable fixture |
The internal ball raceway is not an ordinary thread. Groove profile, internal lead, raceway geometry and ball contact cannot be verified accurately with a standard caliper. These characteristics require specialised production and inspection equipment.
4. Verify the Material and Heat-Treatment Requirement
Material quality should be confirmed through the supplier's material information, production record or requested certificate-not by colour or appearance alone.
DLY standard ball screw nuts use 20CrMo alloy steel. Material selection must be combined with suitable heat treatment because raceway hardness, hardened condition and dimensional stability affect wear resistance and load performance.
If material verification is required for a specific order, confirm the requested document or test method before production. Cutting open a finished nut to inspect the cross-section is a destructive test and is not part of normal incoming inspection.
5. Do Not Remove the Balls for Routine Inspection
The balls inside a ball screw nut are selected and matched to the screw and nut raceways. Their size influences axial clearance, preload, running torque and contact condition.
Removing the balls without the correct procedure can cause:
- Loss of balls from the circulation circuits
- Incorrect ball quantity or sequence
- Mixing of balls from different groups
- Changed preload or clearance
- Damage to seals and return components
A routine customer inspection should evaluate the assembled nut instead. Ball diameter, roundness, surface finish and hardness are production-control items that require suitable measuring equipment and a defined sampling plan.
6. Check the Nut on a Correctly Matched Screw
Running quality cannot be confirmed by holding a loose nut alone. Install it on the correct screw shaft or inspect the matched screw-and-nut assembly supplied by the manufacturer.
If the nut is supplied on a transfer sleeve, do not pull it directly off the sleeve. Press the sleeve against the correctly aligned screw end and rotate the nut gradually onto the shaft to prevent the balls from falling out.
During the running check:
- Support the screw so that bending does not affect the result.
- Move the nut slowly through the available travel.
- Check whether resistance remains reasonably consistent.
- Listen for repetitive clicking, grinding or scraping.
- Observe the seals and ball-return components.
- Do not force the nut through a tight or damaged position.
A local tight point may come from screw damage, contamination or screw straightness-not necessarily from the nut itself.
7. Evaluate Running Torque Correctly
Running torque should be measured with a suitable torque-measuring fixture or instrument under defined conditions. A normal hand tool or torque wrench is not sufficiently sensitive for many ball nut checks.
The result should be compared with the requirement for that specific model, preload, lubrication condition and test speed. A single universal torque value cannot be applied to all ball nuts.
Possible reasons for excessive or fluctuating torque include:
- Excessive preload
- Incorrect ball matching
- Contamination inside the nut
- Damaged raceways or ball-return components
- Insufficient or excessive lubricant
- Misalignment of the test assembly
- A bent or damaged screw shaft
Very low torque does not automatically prove good quality. It may also indicate excessive clearance or insufficient preload.
8. Measure Axial Clearance on the Assembly
Backlash or axial clearance is a relationship between the nut and its matched screw shaft. It cannot be determined by measuring an unassembled nut.
A typical check uses a dial indicator aligned with the screw axis. A controlled axial load is applied in one direction and then reversed while screw rotation is restrained according to the test method. The measured displacement is compared with the confirmed clearance or preload requirement.
The test load, mounting arrangement and measurement position must be recorded. Support-bearing movement, fixture deformation and loose mounting parts can otherwise be included in the result.
For low-backlash requirements, a matched assembly is generally more reliable than ordering a separate nut for an unknown or worn screw. See Can an Anti Backlash Ball Screw Nut Really Remove Backlash?.
9. Check Lubrication and Sealing
Confirm that the lubrication port is open, correctly positioned and compatible with the machine's maintenance arrangement. Inspect grease for dirt, metal particles, water or obvious deterioration.
Seals should sit correctly around the screw without visible cuts, distortion or gaps. They help retain lubricant and reduce contaminant entry, but standard seals should not be treated as a complete enclosure in dusty or chip-producing environments.
Do not judge a new nut as defective only because fresh grease temporarily increases running resistance. Compare it under the specified lubrication and running conditions.
10. Distinguish Incoming Inspection from Factory Inspection
| Incoming inspection | Factory or specialised inspection |
|---|---|
| Model and quantity | Internal raceway geometry |
| External dimensions | Ball diameter grouping and roundness |
| Surface and flange condition | Heat-treatment and hardness testing |
| Running smoothness on matched screw | Raceway lead and profile inspection |
| Basic axial-clearance check | Controlled preload and torque verification |
| Lubrication and seal condition | Material verification and metallurgical testing |
A nut should not be approved solely because it looks clean, and it should not be rejected solely because it cannot be dismantled for internal inspection. The inspection method must match the required performance and available technical documentation.
DLY Ball Screw Nut Inspection
DLY supplies standard, replacement and custom ball screw nuts. Before shipment, relevant checks can include model confirmation, surface condition, screw-and-nut matching, running smoothness, preload or clearance condition, lubrication-port position and protective packaging.
When ordering a replacement nut, send the complete old model, screw diameter, lead, flange dimensions and clear photos. If the existing screw is worn or its internal compatibility cannot be confirmed, a matched ball screw and nut assembly is safer than selecting the nut by diameter and lead alone.
For an explanation of nut structure and circulation, see What Is a Ball Screw Nut and How Does It Work?.
Need to inspect or replace a ball screw nut?
Send DLY the nut model, screw diameter and lead, mounting dimensions, photos and required clearance or preload for checking.
Email: export@dlybearing.com
Contact DLY
