Can an SFU1605 Ball Screw Be Used in a Corrosive Environment?

Aug 07, 2025

Leave a message

Claire
Claire
Linear Motion Application Engineer, DLY Automation Specializing in ball screw and linear guideway selection, system integration, and OEM technical support for CNC and automation applications.

A standard SFU1605 ball screw should not be exposed directly to a strongly corrosive environment. It may operate in mildly humid conditions when the screw is properly lubricated, enclosed and maintained, but continuous contact with water, salt spray, cleaning chemicals, acids or alkaline solutions requires a specially evaluated material and protection system.

SFU1605 describes the ball screw's structure and dimensions, not its corrosion resistance. "SFU" identifies a flanged single-nut series, "16" indicates a nominal screw diameter of 16 mm, and "05" indicates a lead of 5 mm per revolution. None of these designations confirms stainless-steel construction or suitability for chemical exposure.

Why a Standard SFU1605 Can Corrode

A standard DLY SFU ball screw uses an S55C screw shaft and a 20CrMo nut body. These materials provide the hardness, strength and wear resistance required for the rolling contact between the screw raceway, balls and nut. However, they should not be treated as inherently corrosion-resistant materials.

Corrosion usually begins when the protective oil film is removed or interrupted by:

  • High humidity and condensation;
  • Direct water or coolant spray;
  • Salt-containing air or saltwater;
  • Acidic or alkaline cleaning solutions;
  • Process chemicals and corrosive vapours;
  • Fingerprints left on an unprotected raceway;
  • Long-term storage in damaged or open packaging;
  • Insufficient or incompatible lubrication.

Rust on a ball screw is not merely an appearance problem. The screw groove is a precision rolling surface. Once corrosion produces roughness or pitting, the balls repeatedly pass over the damaged area, which may increase running resistance, noise and local contact stress.

When Can an SFU1605 Be Used?

The suitability of an SFU1605 depends on the actual exposure rather than a general description such as "harsh environment." The operating conditions should be divided into practical exposure levels.

Environment Standard SFU1605 suitability Required action
Clean, dry indoor machine Generally suitable Use the correct operating lubricant and normal maintenance
Occasional humidity or condensation risk May be suitable with protection Use an enclosure, maintain the lubricant film and control condensation
Coolant mist or occasional splash Requires careful evaluation Add a bellows or telescopic cover and prevent coolant from washing lubricant away
Frequent washdown or direct water spray Standard exposed version is not recommended Isolate the screw from direct exposure or specify a purpose-designed solution
Salt spray, marine atmosphere or chloride solution Not suitable without special evaluation Confirm material, seals, lubrication, enclosure and corrosion test requirements
Acids, alkalis or aggressive process chemicals Do not use a standard SFU1605 directly Provide the chemical name, concentration, temperature and exposure method for technical review

How to Protect an SFU1605 from Corrosion

1. Keep the Ball Screw Outside the Wet Zone

The most reliable approach is to prevent the corrosive medium from reaching the screw. Where possible, position the SFU1605 away from direct water, coolant and chemical spray. A bellows cover, telescopic cover or sealed machine enclosure can provide more effective protection than relying on the nut seal alone.

Standard nut seals may help retain lubricant and reduce the entry of ordinary particles, but they should not be expected to stop continuous liquid exposure or pressurised washdown.

2. Maintain the Correct Lubricant Film

Lubrication reduces rolling friction and also helps separate exposed steel from moisture. The lubricant must be compatible with the operating temperature, speed, load, seals and surrounding chemicals.

If water or cleaning liquid removes the lubricant, simply applying more grease without cleaning and drying the exposed surface can trap contamination. The source of ingress should be corrected before the lubricant is replenished.

3. Prevent Condensation

Condensation can form when a cold screw enters warm, humid air or when machine temperature changes during shutdown. The screw may appear dry while a thin moisture film develops on the raceway.

Keep the machine enclosure ventilated or dehumidified where necessary, avoid large uncontrolled temperature changes, and inspect the exposed screw before restarting equipment after a long shutdown.

4. Protect the Screw During Storage

An unused SFU1605 should remain clean, dry and covered by an intact rust-preventive oil film. Moisture-resistant packaging and suitable desiccant may be needed for export transportation or extended storage.

Rust-preventive oil used for shipping is not automatically the correct working lubricant. Before commissioning, follow the appropriate cleaning procedure and apply the specified operating grease or oil.

Can the SFU1605 Raceway Be Plated or Coated?

A coating should not be added casually to a finished ball screw raceway. Zinc plating, nickel plating, hard chrome, epoxy or PTFE may provide corrosion protection on some components, but the ball screw groove has controlled dimensions and rolling-contact geometry.

An unsuitable coating may:

  • Change the groove dimensions and internal clearance;
  • Affect ball contact and running torque;
  • Alter preload or motion consistency;
  • Crack or peel under repeated rolling contact;
  • Create hard particles inside the ball-return circuit.

If a corrosion-resistant material or surface treatment is required, it must be confirmed before manufacturing. The specification should consider not only corrosion resistance, but also surface hardness, load capacity, wear resistance, achievable accuracy and compatibility between the shaft, balls and nut.

Does Changing to SFU2005 or SFU2505 Solve the Problem?

No. SFU1605, SFU2005 and SFU2505 mainly differ in screw diameter and related load, rigidity, speed and installation characteristics. Changing from a 16 mm screw to a larger diameter does not automatically improve corrosion resistance.

The environment must be addressed through material selection, lubrication, seals, enclosure and maintenance. Diameter should still be selected according to axial load, unsupported length, critical speed, buckling and machine layout.

What Information Should Be Confirmed Before Selection?

Before approving an SFU1605 for a corrosive environment, provide:

  • The source of corrosion: humidity, water, coolant, salt or chemical;
  • Chemical name, concentration and pH where applicable;
  • Operating and cleaning temperature;
  • Exposure method: vapour, splash, immersion or pressurised spray;
  • Exposure frequency and duration;
  • Required stroke, speed, load and duty cycle;
  • Whether the screw can be enclosed;
  • Required service life and maintenance conditions;
  • Any specified corrosion test or material requirement.

For SFU1605 dimensions and available configurations, review the DLY 1605 ball screw page. For general SFU structure and nut options, see the DLY SFU ball screw series.

For transportation, storage and routine anti-rust measures, read How to Prevent Rust on Ball Screws.

Final Answer

An SFU1605 ball screw can be used in a mildly humid environment only when it remains properly lubricated and protected from direct exposure. A standard exposed SFU1605 is not recommended for continuous water, salt spray, washdown or aggressive chemical contact.

The correct solution should be based on the actual corrosive medium, concentration, temperature, exposure method, required load and maintenance conditions. Do not assume that a larger SFU model, stainless-steel balls or an ordinary aftermarket coating will make the complete ball screw corrosion-resistant.

Need to confirm an SFU1605 for a humid or corrosive application?

Send DLY the medium, concentration, temperature, exposure method, load, speed, stroke and enclosure conditions for an initial technical review.

Email: export@dlybearing.com
 

← Back to DLY Blog

Send Inquiry